Premio Computer Premio Apollo/Shadowhawk Computer Manuale Utente Pagina 73
- Pagina / 122
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
CHAPTER 3
AMI
®
BIOS USERS GUIDE
3-12
Description of the item on screen follows:
IPCA Function
This item allows you to Enabled/Disabled the Advanced Configura-
tion and Power Management (ACPI). The settings are Enabled and Disa-
bled.
Sleep State
This option allows you to set which Sleep State will be used.
S1/POS - Power on Suspend.
The S1 sleeping state is a low wake-up latency sleeping state. In
this state, no system context is lost (CPU or chipset) and hardware maintains
all system context.
S3/STR - Suspend to RAM.
The S3 state is a low wake-up latency sleeping state where all
system context is lost except the system memory. CPU,cache, and chipset
context are lost in this state. Hardware maintains memory context and
restores some CPU and L2 configuration context.
Sleep State LED
This option determines which state the Power LED will use. The
settings are Blinking, Dual and Single. During Blinking, the power LED will
blink when the system enters the suspend mode. When the mode is in Dual,
the power LED will change its color. In Single mode, the power LED will
always remain lit.
- Apollo/Shadowhawk 1
- System Manual 2
- Copyright 3
- Disclaimers 3
- Contents 4
- Getting Started 6
- Setting Up 7
- Switches and Indicators 8
- 4 Premio System Manual 9
- Upgrading 10
- Opening the System Unit 11
- Installing an Expansion Card 12
- Installing a Hard Drive 13
- Getting Help 14
- Keyboard Does Not Work 15
- Mouse Does Not Work 15
- System Unit Problems 16
- Hard Drive Problems 16
- Technical Support 17
- Premio on the Internet 17
- Appendix 18
- Service Under Warranty 19
- FCC Standards 20
- 16 Premio System Manual 21
- Appendix 17 22
- Chapter 1 23
- INTRODUCTION 23
- Mainboard Features 24
- Mainboard Layout 26
- MS-6339 ATX TH1 Mainboard 26
- Chapter 2 27
- HARDWARE INSTALLATION 27
- Central Processing Unit: CPU 27
- CPUFAN: Processor Fan 29
- PSFAN: Power Supply Fan 29
- SYSFAN: System Fan 29
- Clear CMOS Jumper: JBAT1 30
- • Memory Bank Configuration 31
- RIMM1(Bank0+ Bank1) 31
- RIMM2(Bank2+ Bank3) 31
- RIMM3(Bank4+ Bank5) 31
- RIMM4(Bank5+ Bank4) 31
- • Memory Population Rules 33
- Case Connector: JFP1 34
- Floppy Disk Connector: FDD 36
- Primary IDE Connector 37
- Secondary IDE Connector 37
- Power Supply 38
- PIN DEFINITION TABLE 40
- 1 2 3 4 5 43
- 6 7 8 9 43
- Parallel Port Connector: LPT1 44
- Mouse Connector: JKBMS1 45
- Keyboard Connector: JKBMS1 45
- Line Out 46
- USB Connectors 47
- 1-3 Blink 50
- CD-In Connector: J8 52
- AUX Line In Connector: J9 53
- Modem-In: J10 54
- Onboard Audio Codec: JP1 55
- Clear BIOS Password: J18 57
- BIOS Flash Jumper: J17 58
- Audio speaker 59
- USB Front Connector: JUSB1 60
- BIOS USER’S GUIDE 62
- Chapter 3 62
- Enter BIOS Setup 63
- Standard CMOS Setup 65
- BIOS Features Setup 66
- Quick Boot 67
- Try other Boot Devices 67
- Boot up Num Lock 67
- Floppy Drive Swap 67
- Chipset Features Setup 69
- CPU Frequency Ratio 70
- USB Function 70
- Memory Hole 70
- Graphics Aperture Size 70
- IPCA Function 73
- Sleep State 73
- Sleep State LED 73
- Wake Up On PME 75
- Resume By Alarm 75
- PNP/PCI Configuration 76
- Clear ESCD 77
- PCI VGA Palette Snoop 77
- DMA Channel 0/1/3/5/6/7 77
- Integrated Peripherals s 79
- Floppy Controller 80
- Serial Port A/Serial Port B 80
- Serial Port B Mode 81
- IR Duplex Mode 81
- IR Pin Select 81
- Onboard CIR Port 81
- CIR IRQ Select 81
- Port Mode 82
- EPP Version 82
- Onboard Parallel Port 82
- Onboard parallel port set at 83
- Parallel Port IRQ 83
- Hardware Monitor Setup 84
- Chassis Intrusion 85
- Supervisor/User Password 86
- IDE HDD Auto Detection 87
- Chapter 4 88
- BIOS SETUP 88
- Main Menu 89
- Advanced BIOS Features 90
- Boot Up NumLock Status 97
- Gate A20 Option 97
- Typematic Rate Setting 97
- Typematic Rate (Chars/Sec) 97
- Typematic Delay (Msec) 97
- Security Option 98
- HDD S.M.A.R.T Capability 98
- Report No FDD For Win 95 98
- Advanced Chipset Features 99
- AGP Aperture Size (MB) 101
- Integrated Peripherals 102
- USB Controller 103
- USB Keyboard Support 103
- Init Display First 103
- Midi Port IRQ 106
- Power Status LED 106
- Onboard Parallel Mode 106
- PWRON After PWR-FAIL 106
- Power Management Setup 107
- ACPI Suspend Type 108
- Power Management 108
- Video Off Method 108
- Video Off In Suspend 109
- Suspend Type 109
- Modem Use IRQ 109
- Soft-Off by PWR-BTTN 109
- Wake-Up by PCI Card 109
- Power On by Ring 110
- Wake-Up on LAN 110
- CPU Thermal-Throttling 110
- Resume by Alarm 110
- Reload Global Timer Events 111
- PnP/PCI Configuration Setup 112
- Reset Configuration Data 113
- Resource Controlled By 113
- IRQ Resources 113
- PCI/VGA Palette Snoop 113
- PC Health Status 114
- CPU Warning Temperature 115
- Shutdown Temperature 115
- Frequency/Voltage Control 116
- Set Supervisor/User Password 118
- Features 120
- System Requirements 120
- Audio Driver Setup 121
© 2020, manymanuals.it. Tutti i diritti riservati | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale